Ether-FSH2400NS Smart Fast Ethernet Switch Windows In-Band Management 24 × 10/100Base-TX ports Auto MDI/MDI-X VLAN, Priority, Ba
1 Product Overview alert the user when there is a loop formed inside the network on the front panel LED. The management software's diag
1 Product Overview With manual VLAN configuration, both the initial setup and all subsequent moves and changes are controlled by the network admini
2 Preparation before Installation 2 Preparation before Installation Unpack the Package Before you begin the installation of Ether-FSH2400NS Fast
2 Preparation before Installation The Front Panel The front panel is where you can find the twenty-four 10/100Mbps station ports and the LED indic
2 Preparation before Installation AC Power Connector This is a three-pronged power connector where the power cord should be attached. Just plu
3 Installation of the Switch 3 Installation of the Switch Quick Installation Ether-FSH2400NS Fast Ethernet Switch is fully compliant with 10/100
2 Preparation before Installation Fig. 3-2 Attaching the Switch to a 19-inch rack Desktop Installation Ether-FSH2400NS Fast Ethernet Switch
3 Installation of the Switch • The switch should not be placed near large electric motors or other strong electromagnetic sources. As a reference,
2 Preparation before Installation The twisted-pair cable provided an eight-pin plug at each end that mate with the twisted-pair port on the adapter
3 Installation of the Switch Power SwitchPower ConnectorPower Outlet Fig 3-13 Connecting the Switch to power outlet 11 Ether-FSH2400NS Fast
Trademarks All rights reserved. AirLive Logo is an registered trademarks of OvisLink Corp, Taiwan. Other product names and company names are tra
4 LED Indicators 4 LED Indicators Before connecting any network device to Ether-FSH2400NS Fast Ethernet Switch, you should take a few minutes to loo
4 LED Indicators LED Table LED indicator Color Status Meaning System LEDs Power LED Loop LED Trunk LED ● Green ● Yellow ●
5 Management Software Guide 5 Management Software Guide Introduction The Airlive Windows remote management software allows user to configure the
5 Management Software Guide Installing the Software Please follow the procedures below to install the management program into your Windows 1. Ins
5 Management Software Guide Starting the Software 1. To start Management Application, please click on “Run Management Software” button on the C
5 Management Software Guide 3. You can add the switch to the database. So you can access quickly the next time. To do so, please right click on t
5 Management Software Guide There are 4 major functions on the management screen “Network”, “Switch Status”, “Switch Configuration”, and “Switch Int
5 Management Software Guide The port status includes port type, enabled status, link status, speed duplex, flow control, loop detection, and the “R
5 Management Software Guide Byte: The unit display is in number of bytes Packet: The unit display is in number of packets CRC Error Packet:
5 Management Software Guide Signal Quality This test whether the electrical signal on each port is good or bad. Switch Configuration Choos
Table of Contents Table of Contents TABLE OF CONTENTS ...I 1
5 Management Software Guide Global Configuration Submenu Global Configuration is used to configure the global port control registers. Press the R
5 Management Software Guide Port Configuration Submenu Press the “Port Configuration” submenu, and you will see a dialog like follows. Put the chec
5 Management Software Guide Enable: The default is to enable the port. Check the “Disable” if you want to disconnect the port Tx Bandwidth Cont
5 Management Software Guide Right Click ona port to makechanges Port Priority Please right click on a port to change the priority Level Diffser
5 Management Software Guide VLAN Configuration Submenu This page is used to configure the vlan table registers. *Please note that although there is
5 Management Software Guide Port Base VLAN Please make sure you have enabled the port based VLAN in the “VLAN configuration” submenu first. Right
5 Management Software Guide Note: If a port is selected as a member port in a new VLAN group. This port will be removed from the default VLAN gr
5 Management Software Guide *Please remember to press Apply after making changes. Security Configuration This page allow administrators to co
5 Management Software Guide Switch Internals Load Factory Default Settings Press this button to reset the configurations to factory’s default se
Appendix A Product Specifications Ether-FSH2400NS Fast Ethernet Switch Appendix A Product Specifications • Standard Compliance IEEE 802.
Table of Contents Unpack the Package... 4 The F
Appendix A Production Specifications Back Pressure for half duplex • Filtering Address Table 8 K per device • RAM Buffer 2.5 Mbits
Appendix B Troubleshooting Appendix B Troubleshooting This appendix contains specific information to help you identify and solve problems. If
Table of Contents 5 MANAGEMENT SOFTWARE GUIDE ...14 Introduction...
Table of Contents Figures Fig. 2-1 Package Contents ... 4
Table of Contents Tables Table 2-2 Cabling type for 10/100BASE-TX... 9 Table 4-1 Syst
1 Product Overview 1 Product Overview Introduction Windows Remote Management software Conventionally, configuring a switch's smart managem
Commentaires sur ces manuels