Air Live WL-5460AP Manuel d'utilisateur

1 WL5460AP v2 User’s Manual 802.11g Multi-function Wireless

2. Rear Panel: Connection Ports (5460AP / 5460AP v2) Port/button Functions A 12V DC Connects the power adapter plug B LAN1 Connects to Ethernet

5 WL5460AP v2 User’s Manual Factory Default Settings Settin

Hardware Connection Note: Before you starting hardware connection, you are advised to find an appropriate location to place the Access Point. Usually,

7 WL5460AP v2 User’s Manual About the Wireless Operation Mo

Access Point Mode When acting as an access point (default setting), this device connects all the stations (PC/notebook with wireless network adapter)

Client Mode (Infrastructure) If set to Client (Infrastructure) mode, this device can work like a wireless station when it’s connected to a computer so

Client Mode (Ad-hoc) If set to the Client (Ad-hoc) mode, this device can work like a wireless station when it is connected to a computer so that the c

Bridge Mode In this mode, 2 access points in two remote locations connect to each other to provide a wireless bridge between 2 remote LANs. It is most

WDS Repeater Mode A repeater's function is to extend the wireless coverage of another wireless AP or router. For WDS repeater to work, the remote

Universal Repeater Mode A universal repeater can also extend the wireless coverage of another wireless AP or router. But the universal repeater does n

Clause Description EN 300 328 V1.6.1Electromagnetic compatibility and Radio spectrum Matters (ERM); (2004-11) Wideband transmission equipment ope

WISP ( Client Router) Mode WISP (Client Router) mode In WISP mode, the AP will behave just the same as the Client mode for wireless function. However,

WISP + Universal Repeater Mode In this mode, the AP behaves virtually the same as the WISP mode, except one thing: the AP can also send wireless signa

Configuration 1. Start your computer. Connect an Ethernet cable between your computer and the Wireless Access Point. 2. Make sure your wired statio

Mode You can choose and setup different wireless mode for detail configurations Wireless Mode AP Select the AP and press Setup button for Wireles

AP Mode Setting Alias Name You can set the alias name for this device. Limited not exceed 32 characters.  Disable Wireless LAN Interface Check th

Wireless Client Isolation Allow user to set the function Enabled or Disabled. By the function, all wireless clients can't mutual link, but wirele

Encryption WEP Authentication Type You can select Open System or Shared Key type for authentication. Key Length You can set 64bit or 128bit Encryptio

Encryption You can select WPA-PSK (TKIP) or WPA-PSK (AES) method for data encryption. Pre-shared Key There are two formats for choice to set the Pre-

Encryption You can select WPA2-PSK (AES) or WPA2-PSK Mixed method for data encryption Pre-shared Key There are two formats for choice to set the Pre-s

WPA is an encryption standard proposed by WiFi for advance protection by utilizing a password key (TKIP) or certificate. It is more secure than WEP en

WL-5450(5460)AP CE Declaration Statement Country Declaration Country Declaration cs Česky [Czech] OvisLink Corp. tímto prohlašuje, že tento WL-5450(

24 WL5460AP v2 User’s Manual network, you can enter new Fra

25 WL5460AP v2 User’s Manual select the optimal rate. If ob

When Enable Wireless Access Control is checked, only those clients whose wireless MAC addresses listed in the access control list can access this Acc

Client Mode Setting Alias Name You can set the alias name for this device. limited not exceed 32 characters.  Disable Wireless LAN Interface Check t

as a network name because essentially it is a name that identifies a wireless network. Site Survey Site survey displays all the active Access Points

Bridge Mode Setting Alias Name You can set the alias name for this device. limited not exceed 32 characters.  Disable Wireless LAN Interface Check t

Advance Setting Please refer the AP mode settingsÆ Advance Setting for details. AP MAC address Enter 12 digits in hex numbers in the AP MAC address

WDS Repeater Mode Setting Alias Name You can set the alias name for this device. limited not exceed 32 characters.  Disable Wireless LAN Interface

Security Please refer the AP mode settingsÆ Security for details, This setting is use between Wireless client and this device. WDS Security Please r

Universal Repeater Mode Setting Alias Name You can set the alias name for this device. limited not exceed 32 characters.  Disable Wireless LAN Inter

This device uses software which is partly or completely licensed under the terms of the GNU General Public License. The author of the software does no

34 WL5460AP v2 User’s Manual When you are using the univers

WISP (Client Router) Mode Setting Alias Name You can set the alias name for this device. limited not exceed 32 characters  Disable Wireless LAN Inte

Advance Setting Please refer the AP mode settingsÆ Advance Setting for details. WAN port You can select many WAN Access Type : Static IP , DHCP Cli

Audio/Video application, Dialpad internet phone service. or define the special application manually, select the incoming type (TCP/UDP) Incoming start

WISP + Universal Repeater Mode Setting Alias Name You can set the alias name for this device. limited not exceed 32 characters  Disable Wireless LAN

Enable Encryption On You can designate security to use for WLAN side, WAN side or both sides. Both WAN and WLAN side: The security is used on both th

Status In this screen, you can see the current settings and status of this Access Point. You can change settings by selecting specific tab described i

41 WL5460AP v2 User’s Manual Uptime The time period since

． Statistics The Statistics table shows the packets sent/received over wireless and ethernet LAN respectively. ． Active Clients Display the active

TCP/IP In this page, you can change the TCP/IP settings of this Access Point, select to enable/disable the DHCP Client, 802.1d Spanning Tree, and Clo

FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rul

Clone MAC Address You can specify the MAC address of your Access Point to replace the factory setting.

Reboot Click the Reboot button to restart device. 45 WL546

Other ． Upgrade Firmware 1. Download the latest firmware from your distributor and save the file on the hard drive. 2. Start the browser, open the

Reset Settings to Default: Click Reset button to restore the default configuration. ． Password For secure reason, It is recommended that you

This function can list all log information about device. Enable Log Enabled or Disabled display system log information. System All List system all log

Appendix A: Emergency Firmware Upload ． Using AirLive WL-5460AP's Emergency Firmware Upload Feature z The emergency firmware upload feature

Table of Contents INTRODUCTION...

1 WL5460AP v2 User’s Manual Introduction ． WL-5460APv2 is w

2 WL5460AP v2 User’s Manual Features 1. 2x100Mbps LAN port

Parts, Names, and Functions 1. Front Panel: (LED Indicators) (5460AP / 5460AP v2) LED Status Indicator Color Solid Flashing 1 Power Green Turns